As long as the valve stem in your wheel can handle the higher 75 psi rating of the 8-ply Load Range D tire and you don't plan on exceeding the lower weight rating of your wheels then you'll be just fine. If you need to upgrade your valve stem as well then the Americana High Pressure Rubber Snap-In Valve Stem # AM20904 will get the job done since it is rated for up to 80 psi.
If you'd rather have a wheel rated for up to 2,200 lbs (the max rating I'm seeing for an 8-ply tire) then you will... view full answer...
That's actually a really good question and you aren't missing anything.
To be able to add and use the Drill Drive Socket Adapter # DL6456 with the Dutton-Lainson Hand Winch # DL14964, you'll also need to replace the stock handle with part # DL6454. This will give you the square hub so that everything matches up. view full answer...
I have not personally heard of such a thing but I can imagine it being an area of concern. The Electric Jack w/ Footplate # EJ-3520-BBX measures 5-1/4" total forward from the mounting flange. With that information you should able to determine if your tailgate will open or not.
I have attached a picture for you to check out with this measurement along with a couple others. view full answer...
The only way to reduce the force needed to get the bars engaged on weight distribution systems like the Fastway e2 Weight Distribution w/ 2-Point Sway Control part # FA94-00-1000 is to reduce the amount of pitch you have set into the weight distribution system or to use the jack to lift the trailer and truck combination higher.
Of the two options the second is the way to go. Of course you need to chock the wheels on the truck and trailer as you would anyway to be safe but overall this... view full answer...
It's possible we have a hub for your TeeNee trailer, though we don't have any way of knowing off-hand or cross-referencing what hubs you need. So in order to find the correct hubs you will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them.
If you are unable to find them, you need to use a digital caliper and measure your spindle where the bearings ride, like in the... view full answer...
While it may be possible that a 3,500 lb. brake assembly will fit your 3,000 lb. axle, it is recommended that you stay with the 3,000 lb. size intended for your axle and use the part number # K23-472-473-00 for a replacement. If you are dead set on using a 3,500 lb. brake assembly you would need to measure your bearings and brake flange to determine if there is a hub that fits. view full answer...
Based on the dimensions of your 2013 Keystone Passport Ultra Lite 23RB the cover part # 290-64843 would fit and work great. My recommendation though is the Adco Tyvek part # 290-52843 which provides the best protection and has the easiest install. view full answer...
While the MaxxAir Standard RV and Trailer Roof Vent Cover # MA00-933066 isn't designed specifically to be hail resistant if you found yourself in a hail situation where the hail was big enough to damage the cover you'd also be damaging the roof of the trailer. view full answer...
I do have options for you but we don't offer any extended toilet floor flanges unfortunately. Therefore, you'd need to extend the connection to the flange from the tank. I'd simply remove the threaded sections and install 3" diameter ABS pipe from the tank up through the pipe so you can then use the LaSalle Bristol Toilet Floor Flange for RV part # 344633633. view full answer...
Thanks so much for the photos they were super helpful, and based on those we do have the exact Lippert SolidSteps you need. Since your doorway width is just over 25 inches and entry height is just over 34 inches the correct SolidStep is the following:
- SolidStep Manual Fold-Down Steps # LC791572
These steps will fit doors with your width and entry height, though the stabilizer you are referring to will likely need to be removed as it juts out too far. I have added links to the instructions... view full answer...
Hey Ken, we have verified in the pas that the Camco RV fridge vent cover part # CAM42163 works with the Atwood fridges like what you have and is black in color.
The Lippert steps part # LC432690 that you referenced would also work great as a replacement step setup as well. This matches the dimensions you need and would work great. view full answer...
The Adjustable Width Trailer Hitch Receiver part # 13703 is what I recommend for a Keystone Passport. It features a simple bolt-on install once the holes are drilled but you can use the brackets as a template. It has a 3,500 lb gross trailer weight capacity with 350 lb tongue weight rating.
We do offer cage type carriers like the 23x47 Carpod Walled Cargo Carrier for 2" Hitches part # M2205 as well if you're interested. view full answer...
The correct SumoSprings Trailer Helper Springs for overslung axles (axle under leaf springs) is part # TSS-107-40. The springs will be pre-loaded upon installation therefore the space you have between the frame is spring loaded will be less than the height of the spring and bracket. This won't be an issue. view full answer...
We have the current version of the Go Power Automatic Transfer Switch # 34264403 that you referenced. We don't have any older versions in stock so if you ordered this you would receive the current version. view full answer...
The shortest set of guide-ons are the 40 inch # CE27620 that you've looked at. The nice thing about these is that they're constructed of PVC pipe, and they can be cut down further if you wish. As you can see in the video I've linked, the tops of the guide-ons don't stick up very far from the gunwales of the boat. If you were interested in the light-up guide-ons, you could use the # CE27740, and cut those down as well.
If you're on a fairly tight budget, the # CE27620 would work very well... view full answer...
We do not have the ability to install the hitch balls on the weight distribution systems we offer like the FastWay part # FA94-00-1000. You'll need to use a thin walled socket like # ALL643216 to install the ball you go with like # 63840 for a 2-5/16 inch ball. view full answer...
Yes, the 2 blue dots you are talking about is normal for the Prodigy P2 # 90885 and it will take about 15 minutes for those to go off.
When you first put power to this brake controller it displays a "n.c." code which means that it doesn't sense a trailer connected. After 15 seconds the "n.c." code changes to " . ." like you mentioned. This stays on until there is no motion or activity in your pickup for at least 15 minutes. See attached clip from the user manual for more info.
Even with... view full answer...